Whats waiting to be installed on my car...
Senior Member
Joined: Mar 2006
Posts: 9,172
Likes: 0
Vehicle: 2001/Hyundai/Tiburon
yeah mine kinda did this, but they r not on springs, i looked. the knob electronic "box"(contains the lights and board for each knob) right behind the dash are all on a big plastic sheet that is connected at each end, so it bends a little. so i wopuldnt do it often, u might break some plastic.
Senior Member
Joined: May 2001
Posts: 531
Likes: 0
heres my list: hehe
nitrous wet kit(thanks jaws)
the rest of the old mps kit now the cuda 2 kit
future waiting to buy and install:
bigger injectors
clutch
fuel pump
forged piston
Oh and projected mad whp insane hp insane hp lol
nitrous wet kit(thanks jaws)
the rest of the old mps kit now the cuda 2 kit
future waiting to buy and install:
bigger injectors
clutch
fuel pump
forged piston
Oh and projected mad whp insane hp insane hp lol
Thread Starter
Senior Member
Joined: Mar 2002
Posts: 34,642
Likes: 0
From: Los Lunas, New Mexico, USA.
Vehicle: 2001 Hyundai Tiburon, 2004 Kia Sorento, 2010 Kia Soul
Mad, you know what'd be good?
Put on the knobs you like, and run some LED's with wires to the holes in the new knobs. Seal them in place with some clear epoxy or silicone.
That'd kick some ass! There should be room behind the knobs to hide the wire. Just make sure it's flexible. Hell, I think I'll do that now.
Put on the knobs you like, and run some LED's with wires to the holes in the new knobs. Seal them in place with some clear epoxy or silicone.
That'd kick some ass! There should be room behind the knobs to hide the wire. Just make sure it's flexible. Hell, I think I'll do that now.
Senior Member
Joined: Jul 2004
Posts: 9,041
Likes: 0
From: SOUTH Jersey
It is not the lights I am now worried about... I just do not like the HUGE gap between the second gen knobs and my first gen dash... I am waiting to see how the new aluminum knobs for the GK look before I do anything else.. might be a case of something I have to have made... and if I have them made.. I can definatly make them match my Race Air shift knob.
Thread Starter
Senior Member
Joined: Mar 2002
Posts: 34,642
Likes: 0
From: Los Lunas, New Mexico, USA.
Vehicle: 2001 Hyundai Tiburon, 2004 Kia Sorento, 2010 Kia Soul
Java, where can you get that wire? How much? Think that would work?
Mad, I think I get you.
Well, the GK ones I got are nice and small. There is also a ring that goes on the outside of them. I think you can install that recessed a bit and it'll hide that big gap.
Or you could shave down the posts they mount on a bit.
Mad, I think I get you.
Well, the GK ones I got are nice and small. There is also a ring that goes on the outside of them. I think you can install that recessed a bit and it'll hide that big gap.
Or you could shave down the posts they mount on a bit.
Thread Starter
Senior Member
Joined: Mar 2002
Posts: 34,642
Likes: 0
From: Los Lunas, New Mexico, USA.
Vehicle: 2001 Hyundai Tiburon, 2004 Kia Sorento, 2010 Kia Soul
Military Discount. $49 shipped, for a all black one.
Yes, Majin Chithonan had this same one on his doomed tib.
Yes, Majin Chithonan had this same one on his doomed tib.
Senior Member
Joined: Jul 2004
Posts: 9,041
Likes: 0
From: SOUTH Jersey
QUOTE (REDZMAN)
Well, the GK ones I got are nice and small. There is also a ring that goes on the outside of them. I think you can install that recessed a bit and it'll hide that big gap.
Or you could shave down the posts they mount on a bit.
Or you could shave down the posts they mount on a bit.
Oh good point.. I have a nice dremil that would make short work of the shafts (pun intended). Looks like I have a new mod! laugh.gif