heres what im doing today. fun!
Thread Starter
Member
Joined: May 2008
Posts: 58
Likes: 0
Vehicle: 96 accent
heres what im doing today. fun!
well i couldnt really find an off topic forum to post this, so since it has to do with my turbo project i thought i just post it here..
this is what im trying to finish up today.. I ordered my aem fic the other day now im finishing the wiring for the PNP harness... this is my first real solder attempt and its comming out nicely i think.. the solder joints seem strong and im taking my time trying to prevent any head aches later..
heres some pics.
this has been a very educating experience, but also a royal pain in the ass, but its better to do it out of the car than try to fight with soldering this sh*t under the dash in a accent lol
this is what im trying to finish up today.. I ordered my aem fic the other day now im finishing the wiring for the PNP harness... this is my first real solder attempt and its comming out nicely i think.. the solder joints seem strong and im taking my time trying to prevent any head aches later..
heres some pics.
this has been a very educating experience, but also a royal pain in the ass, but its better to do it out of the car than try to fight with soldering this sh*t under the dash in a accent lol
Senior Member
Joined: Aug 2009
Posts: 11,992
Likes: 0
From: Washington D.C.
Vehicle: Hyundai Tiburon FX
hell yeah after a few rounds of that you become a master at soldering!
so how did you take apart the main engine side harness, cut it off? someone gotta break it down for me.
so how did you take apart the main engine side harness, cut it off? someone gotta break it down for me.
Thread Starter
Member
Joined: May 2008
Posts: 58
Likes: 0
Vehicle: 96 accent
all done
well for now.. its time for testing.. ive ran through it several times with my ohm meter to make sure the connections are accurate and they all are.. now im going to install with bypass plugs to see if car runs.. if it does success then its time for tape and try to make it look decent... im trying to decide what to do with the wires not being used.... was thinking cut them but i may just tape em into the harness... i dunno.. but yea the rst round i made a mistake with the harness plug orientation i had it all backwards ... so i got another and started over this time should be all good..
i just reach up the dash and cut the wires for the harness plug... the ecu connection i took apart a oem ecu and then destroyed it and cut the pins so i could solder wires to em.... i figured since this was 350$ spent last week i cant buy anyhting else at the moment ill just finish wiring it up i may just through the fic it n.a see how it drives ... but i still need to modify the mounting bracket im using and mount the fic in the car and figure out a vacuum line,
well for now.. its time for testing.. ive ran through it several times with my ohm meter to make sure the connections are accurate and they all are.. now im going to install with bypass plugs to see if car runs.. if it does success then its time for tape and try to make it look decent... im trying to decide what to do with the wires not being used.... was thinking cut them but i may just tape em into the harness... i dunno.. but yea the rst round i made a mistake with the harness plug orientation i had it all backwards ... so i got another and started over this time should be all good..
i just reach up the dash and cut the wires for the harness plug... the ecu connection i took apart a oem ecu and then destroyed it and cut the pins so i could solder wires to em.... i figured since this was 350$ spent last week i cant buy anyhting else at the moment ill just finish wiring it up i may just through the fic it n.a see how it drives ... but i still need to modify the mounting bracket im using and mount the fic in the car and figure out a vacuum line,
Thread Starter
Member
Joined: May 2008
Posts: 58
Likes: 0
Vehicle: 96 accent
its works lol.. i put it in the car and the fic was running perfect for about 20 mins till i removed it lol...
i made some changes and the were applied everything seems good. now i need to find a good cheap scan tool to read stft since the one i have doesnt do it.... any suggestions?
i made some changes and the were applied everything seems good. now i need to find a good cheap scan tool to read stft since the one i have doesnt do it.... any suggestions?
Administrator
Joined: Mar 2006
Posts: 12,515
Likes: 2
From: Lacey, WA
Vehicle: Two Accents, Mini, Miata, Van, Outback, and a ZX-6
Congrats on getting it working!
My Innova scantool can read STFT and LTFT as well as read/reset trouble codes and display other live data and was only about $80. I think they're even cheaper now.
My Innova scantool can read STFT and LTFT as well as read/reset trouble codes and display other live data and was only about $80. I think they're even cheaper now.
Thread Starter
Member
Joined: May 2008
Posts: 58
Likes: 0
Vehicle: 96 accent
QUOTE (187sks @ Feb 3 2010, 01:33 PM)
Congrats on getting it working!
My Innova scantool can read STFT and LTFT as well as read/reset trouble codes and display other live data and was only about $80. I think they're even cheaper now.
My Innova scantool can read STFT and LTFT as well as read/reset trouble codes and display other live data and was only about $80. I think they're even cheaper now.
ill look into it thanks.. i saw the elm 5 which would be 72$ shipped... i saw a bunch on ebay for like 30$ but i dont trust em lol...
well now i got the turbo and engine management done lol... next is clutch and tranny and a couple engine to build...
