I have 2 American Bass 12s in a Ported box, and a Rockford Fosgate 300W at 2 Ohms Bridged mono Amp for sale...

<u>American Bass 12's</u>
http://i10.photobucket.com/albums/a1...0905/myamp.jpg
Ultra Thick Chrome-Plated Deep Bottom Basket.
NT Multilayer Foam Surround for Better Stable Linear Exclusion.
Stiff and Rigid non-press Paper Cone.
Inverted Dust Cap further increases Cone's resistance to flex under Pressure
Dual Black Mirror Tinsel Lead Wires.
Sleeved High Power Tinsel Lead Wires to resist Lead breakage.
Blackened Motor Parts for Superior Heat Dissipation & Long Life
Hi-Temp Anodized Aluminium Voice Coil Bobbin with Nonex Protection.
Ultra-Length Voice Coil for High excursion without Distortion.
Hyper extended Pole Piece Increases Accuracy, raises Induction.
Special Cooling Vents of Deep Bumped Back Plate to Increase Power Handling.
Uni-Rubber Gasket for Airtight Seal in Mounting.
Rubber Magnet Boot Protects Magnet.
Single Voice Coil 4 OHM

Retail Value : $120 each speaker

<u>Rockford Fosgate 150 Watt Amplifier with Wired Remote Punch Bass Control</u>
http://i10.photobucket.com/albums/a122/cdu...AmericanB12.jpg
150 watts RMS power x 1 at 4 ohms
300 watts x 1 bridged RMS power at 2 ohms
CEA compliant
Variable 40-400 Hz low-pass or high-pass crossover
12 dB/Octave Butterworth crossover alignment
Variable 0 - 18 dB Punch Bass EQ at 45 Hz
Removable chrome sound
4 gauge power and ground connections
Built-in ATC fusing
Preamp outputs
Illuminated RF logo with output level display
Wired remote Punch bass control
TRANS-ana (TRANSconductance Active Nodal Amplifier) design simplifies the input circuit path for transparent and uncolored sonic performance
MEHSA (Maximum Efficiency HeatSink Application) yields up to 5 times better heat transfer from the Mosfet devices to the heatsink
Focused Mass heatsink places critical aluminum material where it's needed the most to keep the amplifier cool for increased efficiency and reduced distortion
Variable Voltage Power Supply Optimization "loosely" regulates the power supply circuitry for maximum output power at any given battery voltage
Custom designed TO-247 output Mosfets have 60% more metal tab area for improved thermal stability and wider linearity
Military Specification (Mil Spec) Glass Epoxy circuit boards accept larger copper traces for better current flow and resist vibration much better than inferior fiberglass circuit boards

Retail Value : $200

Box Retail Value: $100

This system hits vary hard! Especially in the tib! I have had this system for less than a month...and I am selling it because i want to start doing stuff to my engine! I spent over $500 for this, so your getting a deal! I am letting this go for $400! The system is practically brand new! For more pics, PM me...

 

for the pics of the subs up uploaded the amp
and for the amp you uploaded the subs

lmao.gif

 

400? I might be able to get you 200 for it.

 

Whoops...my bad!

Ssyak..I cant let it go for that cheap, sorry man! The system is too new!

Here are some pics of the system in my tib....
The last picture is the pic of the bass controller, and i just put it in my ash tray...seein how i dont smoke

http://i10.photobucket.com/albums/a122/cdu.../Picture006.jpg
http://i10.photobucket.com/albums/a122/cdu.../Picture007.jpg
http://i10.photobucket.com/albums/a122/cdu.../Picture008.jpg
http://i10.photobucket.com/albums/a122/cdu.../Picture010.jpg
http://i10.photobucket.com/albums/a122/cdu.../Picture013.jpg

Hey swift...I tried to pm you..but it wouldnt send because your inbox is full or somethin? But hit me up on here, and we'll discuss the deal...

 

System is still up for grabs....

 

i'd love to have it...but 400 is just too much for me right now...nice system though

 

thanks carolla

yea...i want to keep it...but i also want to start doing stuff to my engine! But now im not sure if im going to be able to do stuff to my engine, because i have to start saving for college!

 

^^take it from me...college and tuning does NOT work out so well.

good deal though, someone jump on this if you like BASS.