Venom IM for 2.0 Beta
06-18-2002, 04:50 PM
#1
Senior Member
Thread Starter
Join Date: Feb 2002
Posts: 239
Likes: 0
Received 0 Likes
on
0 Posts
Venom IM for 2.0 Beta
Does anyone know where I can get one of these for my 01 Tib?
I know they exist. I don't really like the idea of having my stock IM bored out. I would rather get a replacement one that wil reach at least 61mm to match the throttle.
Z?
I know they exist. I don't really like the idea of having my stock IM bored out. I would rather get a replacement one that wil reach at least 61mm to match the throttle.
Z?
06-19-2002, 10:58 AM
#6
Senior Member
Join Date: Aug 2001
Posts: 921
Likes: 0
Received 0 Likes
on
0 Posts
Nah, that's the throttle body. The intake manifold inlet port is about the same from the factory(56mm), but can be bored out past 63mm, someone said up to 70mm I think but I don't know how much would be left around the edges.
06-20-2002, 12:09 AM
#7
Senior Member
Thread Starter
Join Date: Feb 2002
Posts: 239
Likes: 0
Received 0 Likes
on
0 Posts
Are you sure?
I believe I was told from Onpol that they could only do 58mm at most.
Interesting, though I remember hearing that someone had a 60mm one in their tib that was the stock just bored outward.
Oh well, I want chrome!
Z?
I believe I was told from Onpol that they could only do 58mm at most.
Interesting, though I remember hearing that someone had a 60mm one in their tib that was the stock just bored outward.
Oh well, I want chrome!
Z?
06-20-2002, 02:07 AM
#8
Super Moderator
Join Date: May 2001
Location: Rancho Palos Verdes, CA
Posts: 11,851
Likes: 0
Received 2 Likes
on
2 Posts
Vehicle: 2008 Toyota Prius 2006 Suzuki SV650S
The stock TB can only be bored out to 58mm. Unless you reinforce the backside of it with JB weld or some similar epoxy type substance.
The SR "stock" 58mm throttle body can be bored out over 60mm. The "barney" TB could also be bored out to over 60mm.
Keep in mind, the IM needs to be bored out to match, and there is such a thing as TOO BIG. A 85mm throttle body would flow great amounts of air...but it would move very slowly due to the small volume of air our engines require. It would also be very hard to modulate the throttle, as from say, half throttle to Full throtlle would make no difference as the engine's demand for air would be met by just half or 3/4 throttle.
The SR "stock" 58mm throttle body can be bored out over 60mm. The "barney" TB could also be bored out to over 60mm.
Keep in mind, the IM needs to be bored out to match, and there is such a thing as TOO BIG. A 85mm throttle body would flow great amounts of air...but it would move very slowly due to the small volume of air our engines require. It would also be very hard to modulate the throttle, as from say, half throttle to Full throtlle would make no difference as the engine's demand for air would be met by just half or 3/4 throttle.
06-20-2002, 10:54 AM
#9
Senior Member
Thread Starter
Join Date: Feb 2002
Posts: 239
Likes: 0
Received 0 Likes
on
0 Posts
I had no intention of boring the throttle either. Wasn't the Barney BBTB adjustable up to 61 anyway to match the intake manifold set with a bore of 61mm that I am looking for from venom?
Thanks for verifying the facts about the IM.
Z?
Thanks for verifying the facts about the IM.
Z?