Zekon kit
06-17-2004, 10:29 AM
#12
Senior Member
Join Date: Jul 2004
Posts: 302
Likes: 0
Received 0 Likes
on
0 Posts
QUOTE (KayJai)
QUOTE (Arch93086)
Well my front bumper does resemble that one. I was thinking of pushing the lights out with washer behind the bolts. Anyone have any other ideas of how to fill the gap? (It's not anywhere near close to the pic though)
Outta curiosity,... is your front bumper cut / shaped the same as it is onto here:
Where it's almost cut / notched out flat / straight on the Passenger side top?
Unfortunately, yes it is.
06-23-2004, 08:28 AM
#15
Senior Member
Join Date: Feb 2004
Location: Kitchener, Ontario, Canada
Posts: 356
Likes: 0
Received 0 Likes
on
0 Posts
great.. now I am worried what mine will look like when done.. Would post some pics.. but the digitalcamera (40.oo! w00t!).. is.. a 40.oo camera.. so quality is less then kr@p.. my rear looks a whole lot different then that one.
06-23-2004, 08:43 AM
#16
Senior Member
Join Date: Jul 2004
Posts: 302
Likes: 0
Received 0 Likes
on
0 Posts
Well don't be too worried. If you take it to a decent shop it should look a lot better than that. I have the same one and even Maaco made it look tons better than that. You will have to do some light modifying to it though.
06-25-2004, 12:25 PM
#19
Senior Member
Join Date: Feb 2004
Location: Kitchener, Ontario, Canada
Posts: 356
Likes: 0
Received 0 Likes
on
0 Posts
Well, I seriously have to tell anyone who asks about this kit.. DO NOT BUY IT! with all the problems.. this is the best one... The side skirts, don't even fit on mine.. what so ever!! the driver side is 1/2" too short from the back.. and the passnger is about 1/4" to short from the back of the door! So, I have 2 useless parts!
I will be contacting them directly thru email and phone.. and will keep calling them **** nuts, until they provide me with 2 pieces that fit. if not It is off too WW for their side skirts.. or the "V-Side"
I told them, they can have the skirts back and that they can burn them!
So, if you plan on getting this kit.. don't.. you'd probably have better luck with something else.
I will be contacting them directly thru email and phone.. and will keep calling them **** nuts, until they provide me with 2 pieces that fit. if not It is off too WW for their side skirts.. or the "V-Side"
I told them, they can have the skirts back and that they can burn them!
So, if you plan on getting this kit.. don't.. you'd probably have better luck with something else.
07-08-2004, 01:50 AM
#20
Junior Member
Join Date: May 2004
Posts: 22
Likes: 0
Received 0 Likes
on
0 Posts
Goddamn it!! Every bloody kit I look at ends up "Do Not Buy!" What is it with these kit makers that they can't get it right for Hyundai's?!
I can't go Veilside cus they don't have 1st gen one anymore and to get 2nd gen over to UK would cost £6k! And I've been recommended not to go Vader!
I don't want to go Wings West, cus it doesn't make the front of the car look any different than stock when looking at it from the side! I do like their rear wing though and would probably buy that.
Cuda, I'm not really keen on the front, too chunky
Erebuni, I've heard bad reports about them as well.
ATH - again, same problem as with Wings West - not much difference in look on the front bumper.
Zefiro, can't find any 1st gen kits available.
So basically, to get a good kit that's made for our car, we've basically got to go custom designing then?!
I can't go Veilside cus they don't have 1st gen one anymore and to get 2nd gen over to UK would cost £6k! And I've been recommended not to go Vader!
I don't want to go Wings West, cus it doesn't make the front of the car look any different than stock when looking at it from the side! I do like their rear wing though and would probably buy that.
Cuda, I'm not really keen on the front, too chunky
Erebuni, I've heard bad reports about them as well.
ATH - again, same problem as with Wings West - not much difference in look on the front bumper.
Zefiro, can't find any 1st gen kits available.
So basically, to get a good kit that's made for our car, we've basically got to go custom designing then?!