2003 GK partout
 

STIPULATIONS.



1) Pieces may take time to be shipped, be patient. I am a military member and training season is approaching very fast, I will be super busy but will get your parts out and provide adequate tracking when it happens. If you expect miracles go ask Santa or Baby Jesus.



2) Shipping is NOT included in any of these prices.







ENGINE:

-Tial 38mm wastegate with dump pipe and springs (BIG red, SM green, BIG blue, SM blue) $150

-ARK 3” single exhaust SOLD and DELIVERED

-Valeo XTRM clutch kit w flywheel $200 (slave cylinder and braided hose FREE with purchase)

-Vacuum Manifold $25

-Earls braided clutch hose with new slave cylinder $50



BRAKES ($300 for all listed below, shipping not included)

-Kspec front BBK $350

-Earls braided brake hoses $75

-Drilled and slotted rear rotors $40

-Russels speed bleeder screws (free with purchase of all brake items)



BODY and SUSPENSION (both bars together $100)

-F/L headlights, prewired for 03, $285 shipped within the 48 States.

-DC Sports front strut bar SOLD and DELIVERED

-OEM Elantra XD front sway bar $75



ELECTRONIC STUFF (both gauges together $150)

AEM UEGO wideband kit $120

AEM digital voltage gauge $50



Wategate is missing two little bolts, one of the holes is in rough shape but does hold, I lost the bolts during removal to swap internal springs.



http://i228.photobucket.com/albums/e...psxvawtkxy.jpg



http://i228.photobucket.com/albums/e...ps3nqfvxd6.jpg



http://i228.photobucket.com/albums/e...pseh33nyiz.jpg



http://i228.photobucket.com/albums/e...pstzoeyuzk.jpg



http://i228.photobucket.com/albums/e...psz499xk7f.jpg



http://i228.photobucket.com/albums/e...ps5qs2wom9.jpg



http://i228.photobucket.com/albums/e...ps12e31d8b.jpg



http://i228.photobucket.com/albums/e...psbfgkvfrf.jpg



http://i228.photobucket.com/albums/e...pse9wr51pd.jpg



http://i228.photobucket.com/albums/e...pscqwjttkl.jpg



http://i228.photobucket.com/albums/e...psji8jimvr.jpg



http://i228.photobucket.com/albums/e...psj0qk5lxm.jpg



So new the stickers are still fully attached.



http://i228.photobucket.com/albums/e...pstbvtoaif.jpg



http://i228.photobucket.com/albums/e...psepnv1gmy.jpg



http://i228.photobucket.com/albums/e...pspsjjlzoj.jpg



http://i228.photobucket.com/albums/e...ps90ivuugj.jpg



Back of the wideband gauge. (6 wires connect to the sensor, small connector with 4, 12v and ground, white is 5v out, snipped blue wire is unused)



http://i228.photobucket.com/albums/e...psyg29og9b.jpg





http://i228.photobucket.com/albums/e...psqnuyyzee.jpg





http://i228.photobucket.com/albums/e...ps6anlnnbq.jpg



Back of voltage gauge. (only requires a 12v and ground to work)



http://i228.photobucket.com/albums/e...ps1ma7tq67.jpg



Thickness of front sway bar. (GK front bar in BOTH i4 and V6 are 18.8mm and 21.8mm, if you have a 4cyl the bar is 18.8mm, if you have a V6 with a YELLOW dot on your bar it is 21.8mm, if the dot is RED it is 18.8mm...either way, this one is thicker.)



http://i228.photobucket.com/albums/e...psky6gxbkl.jpg

Pm sent! Sad to see that you're parting out the tib!

The Gk mounts wont work on an RD will they?

The pistons are a must, and I really need the rods but not sure I can swing that at the moment.





PM sent

Sad day when a car like this is going to be part out.

I don't know if I can let you do this

Nnnooooooo ooo ooooo ooooo ooooooo oooo .....

I'd like to take the Ferrea valvetrain off your hands but didn't know if you were actually disassembling the motor or not. Any headwork done by anychance? Might be able to take the whole head if you're willing to go that route.

I will take the head with or just the ferrea valvetrain If spoolin doesn't take it pm me your pay pal.

Is anyone a member on new tiburon? If so, any chance someone could get ahold of OP letting him know people are interested in this thread?

Next in line with Ferrea parts or head.